Capacity: 27" W x 18" H
Blade: 1.5" x 21 '0" x .050"
9.2° Permanent Arm Tilt
Motor: 10 HP
Hydraulics: 5 HP
Bar-Feed: 0-24" Stroke Hydraulic Cylinder (Multiple Index)
The Control Console is located on the front of the saw, in a swing-away console, for operator convenience.
The Touch Screen display provides easy-to-use menu navigation for programming and recalling automatic saved jobs, running a series of jobs, as well as manual functions and programming information required for each job. Other functions include memory storage for a job library, system information, diagnostics and saw operation parameters.
The Auto Run screen controls the Computer Controlled Feed system which makes programming and running a job in automatic easy. Any pre-saved job can be entered into the Auto Run, or the operator can program a job. The quantity, length, height, width, and blade speed are then entered and transferred to the Auto Run. The information can then be saved as a job, and can be operated on the saw at any time.
Jobs can be programmed into the touch screen then saved with a job number to run at any time. Up to 999 jobs can be saved. The part length, height, width, and quantity are entered for the cut, and then transferred to run automatically. Blade speed, blade type, and cutting options are also set before transferring to run automatically.
A series of cuts for certain parts can be programmed, to be cut from the same bar stock, by entering up to 12 jobs that will be run in a sequence. The sequence can be run up to 99 times by placing an amount into the "Reps" section. Up to 100 program series can be created and saved in the menu.
In Manual Run mode, the saw operator can make a single, semi-automatic cut without creating a program. The blade and various options can be controlled from this screen, or the console.
The control panel allows for quick I.O. and system operation to calibrate the encoders and help diagnose a possible problem with operation of the saw.
The patented Cut Watcher system monitors the cut for squareness to a pre-set deviation value. The system shuts down the saw when the pre-set value is exceeded. This is a must for production cutting.
Help files are available to assist in operating the saw. These include: a blade symptom chart, length converter, basic calculator, saw safety section, and blade change instructions.
The saw arm Feed Rate can be adjusted from zero to 3 inches per second. Cutting pressure can be adjusted for effective metal removal rates.
A Full-Stroking Bi-Directional Main and Feed Vise clamp material at the turn of a switch, and holds the material in place to ensure accurate cuts. The clamping pressure is easily adjusted to clamp various materials.
A standard Roller Discharge Table provides easier handling after the cut. The table is 24" in length and is fully coolant panned.
The Bar-Feed on the saw is comprised of an automatic floating (self-adjusting) shuttle vise feed system with a 0-48" feed stroke with multiple indexing for longer parts. This efficient system prevents binding of imperfect material. The Material Jogging feature allows the operator to inch the material forward.
The Blade Guide System incorporates side and back blade guides that utilize carbide inserts for long wear, stability and maximum blade support.
In addition to precision-ground flat carbides, roller guides are also used which reduce vibration when cutting hard materials.
A shaft-driven Blade Brush is standard for positive removal of metal chips that lodge in the blade gullets. This system ensures a cleaner blade, more accurate cuts, and prolonged blade life.
Blade speed can be adjusted with an infinitely variable speed drive, which allows the user to adjust blade speed's surface feet per minute which is set and adjusted from the Touch Screen.
The Powered Guide Arm provides optimum blade support as material size changes. The guide arm works in conjunction with the main vise to adjust automatically while holding the blade securely, providing straighter cuts and longer blade life.
The Powered Blade Tensioner maintains proper blade tension at all times during the cut, compensating for blade stretch. Changing blades on the saw is done in minutes, with the use of the Powered Blade Tensioner.
The saw is equipped with a safety Emergency Stop cut-off switch. This allows the operator to closely monitor the cutting process and quickly stop it if needed.
The Safety Lockout Key is used to disable saw operation during maintenance.
The saw will automatically shut off if the blade breaks or is out of stock, shown by the Broken Blade or Out-of-Stock Indicators.
The Panic Stop haults all automatic functions.
The saw has a totally built-in coolant system with sealed coolant pump, with coolant that is dispensed through a flex-tube nozzle to flood the center of the cut. A cutting fluid clean-up hose is provided for machine wash down.
The Chip Conveyor removes chips from the cutting area into an easy-to-empty container. Chips and coolant are automatically separated into two different containers.
The Optional Computer Controlled Traverse, or CCT, controls the feed rate and cutting force to maintain the optimum cutting rate.
With the CCT option, a Material List is provided with the touch screen. The list includes the recommended blade speeds, cutting rates and blade pitch for the type and size of material. The data can then be transferred to a job and run automatically or manually.
An Optional Outboard Vise on the Discharge helps with clamping of material.
An Optional 3rd Vise on the Feed helps with clamping of material.
Full Capacity Top Clamps can be added to the Main and feed vise, or just the main vise for vertical clamping of structural shapes and when entire "mill bundles" are to be cut.
A Full Capacity Top Clamp can be added to the outboard vise for vertical clamping of structural shapes and when entire "mill bundles" are to be cut.
The optional spray mist system lubricates the blade with a mist that is adjustable at a rate of 4 - 200 pulses per minute, pushing the mix of oil/air out of the delivery line to the nozzle.
A high intensity light that casts a shadow of the blade onto the material to be cut, indicating the exact spot where the blade will enter the material.
An Optional Laser Light indicates either above or below where the blade will enter the material for the cut.
0-120" Stroke Servo Twin Ball-Screw Bar-Feed
Optional 5' or 10' Idle or Powered Roller Stock Table
5' or 10' Discharge Table Extension